本帖最后由 yangyangshu 于 2013-6-19 18:50 编辑
我们公司的做法是,封头的曲率样板或球罐的曲率样板我们自己制作,自己检验,在规程中有一个专门的《测量和试验设备管理规程》,在这个规程中,则专门有一段规定了“曲率样板的校验”,详细规定了自制的曲率样板的标识、编号、曲率样板与标准曲率误差的规定、自己校验的方法等内容。
具体内容摘抄如下:
4.5 calibration for curvature template
4.5曲率样板的校验
4.5.1 The identification oncurvature template shall include name of company and symbol、 Standardcurvature value、numbering、production date etc withcontent clear and visible. The working end cutting edge of curvature templateshall be free from hitting、fracture、warping and other obviousspot and scratch that affecting using.
4.5.1曲率样板上的标识,应包含本公司名称及标志、标准曲率值、编号、生产日期等信息,内容应清晰可见。曲率样板的工作端刀口不应有碰伤、断裂、翘曲及影响使用的明显斑点、划痕。
4.5.2 The curvature deviationbetween any positions of working end of curvature template and standardcurvature shall be not greater than the provisions in table 1 below.
4.5.2曲率样板工作端任意位置曲率与标准曲率之间的差值不应超过表1的规定。
provisionsfor deviation between curvature template and standard curvature 表1:曲率样板与标准曲率误差的规定 unit:mm 单位:mm
chord length of lower end of curvature template been checked 被检曲率样板下端弦长 | ≤500 | 501~1000 | 1001~2000 | 2000~3000 | >3000 | gap between curvature of any positions of curvature template and standard curvature 任意位置曲率与标准曲率之间的间隙 | ±0.2 | ±0.3 | ±0.4 | ±0.5 | ±0.6 |
4.5.3 Lay down the curvaturetemplate on solid fiberboard and stick closely, draw the shape of curvature onthe solid fiberboard, and then draw out coordinate graph by taking the bottomline of curvature template as horizontal ordinate and one end as circle center,take several points on the working end of curvature template and measure outhorizontal and vertical ordinate respectively. Calculate the value of standardcurvature on computer and make comparisons.
4.5.3将被检曲率样板平放在硬质纸板平面上,贴紧,在硬质纸板上描出曲率样板的形状,然后以曲率样板的底边为横坐标,一端为圆心,作出坐标图,在曲率样板工作端面上取几个点,分别量出横纵坐标。在电脑上计算出标准曲率的数值,与之进行比较。
此外,规程中还附有专用的 “CALIBRATION RECORD FORCURVATURE SEGMENTAL TEMPLATE 曲率样板标定记录”
论坛上不是有个帖子提供的是QC Manual 及QC Procedue 的下载吗?那个QC Manual 及QC Procedue 完全是抄袭我公司的文件,QC Manual 及QC Procedue都是本人亲自编辑的,连格式都没重新编辑呢,甚至分享的资料文件属性里面还可以看到本人作者的名字以及本人单位的名字,呵呵。这个QC Procedue 里面就有我编写的《测量和试验设备管理规程》,里面有上述内容。
这样做也得到了AI的认可,在取证及换证中都没有提出什么异议。
我们的做法你可以参考下。
|