ASTM A516 - 70在那一分卷找

jimhou1

我下载了ASTM VOL1 8个SECTION下来，怎麽会找不到ASTM A516 的项目，是不是没有修改的就没放进去 ? 请先达帮帮忙解说一下 ?

betterxu

betterxu 发表于 2015-11-6 16:09
可以去ASME 找……

http://www.astm.org/Standards/A516.htm
最新版是2015，可是你可以看下这个链接，常用机械性质看下面。

ASTM A516 / A516M - 10(2015)
Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
Active Standard ASTM A516 / A516M | Developed by Subcommittee: A01.11

Book of Standards Volume: 01.04

        Format        Pages        Price         
        PDF        4        $39.00          ADD TO CART
        Hardcopy (shipping and handling)        4        $39.00          ADD TO CART
Historical Version(s) - view previous versions of standard
ASTM License Agreement
Shipping & Handling
MORE A01.11 STANDARDSRELATED PRODUCTSSTANDARD REFERENCES
Abstract

This specification covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important. According to different strength levels, the plates are available in four grades: Grades 55, 60, 65, and 70. The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements. The steel shall be killed and shall conform to fine austenitic grain size requirements. The mechanical properties such as tensile strength, yield strength, and elongation shall be determined by a tension test for the plates.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification2 covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important.

1.2 Plates under this specification are available in four grades having different strength levels as follows:


 Grade U.S. [SI]
Tensile Strength,
ksi [MPa]
55 [380]
55–75 [380–515]
60 [415]
60–80 [415–550]
65 [450]
65–85 [450–585]
70 [485]
70–90 [485–620]
1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification as follows:


 Grade U.S. [SI]
Maximum Thickness,
in. [mm]
55 [380]
12 [305]
60 [415]
 8 [205]
65 [450]
 8 [205]
70 [485]
 8 [205]
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results of Specification A20/A20M apply.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
Keywords
Boilers And Pressure Vessels - Low-Temperature Services - Notch Toughness - Plates - Pressure Vessels - Sheet, Strips And Coils - Welded Steel Plates - Welded Steel Sheets - Welded Steel Strips

ICS Code

ICS Number Code 77.140.30 (Steels for pressure purposes)

UNSPSC Code

UNSPSC Code 30102204(Steel plate )
Referencing This Standard
DOI: 10.1520/A0516_A0516M-10R15
ASTM International is a member of CrossRef.
Citation Format
ASTM A516 / A516M-10(2015), Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service, ASTM International, West Conshohocken, PA, 2015, www.astm.org

betterxu

可以去ASME 找……

gbt8163

暂时没有A516，请从其他途径找吧。

jimhou1

gbt8163 发表于 2015-11-6 15:13
暂时没有A516，请从其他途径找吧。

gbt8163楼主，谢谢您的帮忙，这种现象是不是常态，暂时空号是偶然或常态，会不会是改号码，或是并到那一譬号码去了 ? 我看ASME II-A，SA516引用的还是A516/06年的而已，会不会没改就没放进去 ?

jimhou1

betterxu 发表于 2015-11-6 16:09
可以去ASME 找……

谢谢，我到2015 ASME II-A PART B去找，目前ASME还是抄 ASTM 2006版，不晓得ASTM A516最新的是那一年版 ?

twan13

因为还有没发的section，这次到手的的缺全，但是因为太全所以好多常用的不在头几个section里。

lw6688

材料好像不是很全，还是慢慢找吧

pj2998

Volume 01.04 Steel--Structural, Reinforcing, Pressure Vessel, Railway