|
|
发表于 2021-5-15 08:19:30
|
显示全部楼层
本帖最后由 qldch2306 于 2021-5-15 08:23 编辑
前 言
本标准按照GB/T 1. 1-2009《标准化工作导则 第1部分: 标准的结构和编写》 的要求编写。
本标准由天津市市场和质量监督管理委员会提出并归口。
本标准起草单位: 天津市特种设备监督检验技术研究院、天津市滨海新区塘沽锅炉压力容器检验所、
天津大学。
本标准的主要起草人: 赵秋洪、 司永宏、 韦晨、 刘怿欢、 刘子方、 刘永长、 段瑞、 祖宁、 高宏、 高
利慧、 王恒、 刘宏臣、 李卫星、 惠楠、 牛卫飞、 王泽军、 萧艳彤。
钢制承压设备焊接接头超声相控阵检测
1 范围
本标准规定了钢制承压设备焊接接头超声相控阵检测的术语和定义、 一般要求、 扫描类型及显示方
式的选择、 检测和质量分级、 报告和存档。
本标准适用于壁厚为3. 5 mm~200 mm铁素体钢制承压设备全熔化焊焊接接头的检测, 也适用于在役承压设备焊接接头的超声相控阵检测。
本标准不适用于奥氏体钢制承压设备焊接接头的超声相控阵检测。
最小可检测壁厚3.5???有的标准 如DB37T 4360-2021中大径管道焊接接头相控阵超声检测技术规程规定 6.0mm。。。
适用于外径大于或等于100 mm, 且厚度为6 mm~150 mm的细晶钢制环向对接接头, 以及安放式筒体(封头) 公称直径≥300 mm或插入式筒体(封头) 公称直径≥500 mm, 接管公称直径≥100 mm的
角接接头的检测。 对于厚度超出以上范围的焊接接头, 经过工艺验证试验, 具有足够的检测灵敏度后,参照本文件执行。
本文件不适用于粗晶材料和奥氏体焊接接头的检测。
NBT 47013.15 适用于板厚为 6mm~ 250mm 的碳素钢、低合金钢制承压设备用板材的相控阵超声检测方法和质量分级。
5.7.1.1 本条适用于外径不小于 12mm 的承压设备用碳钢、低合金钢、奥氏体不锈钢及奥氏体-铁素体双相不锈钢无缝钢管超声检测
方法和质量分级。(壁厚很薄的!)
ASTM E2700-2020 规定:This practice uses angle beams, either in S-scan or E-scan modes, primarily for butt welds and Teewelds. Alternative welding techniques, such as solid state bonding (for example, friction stir
welding) and fusion welding (for example, electron beam welding) can be examined using this
practice, provided adequate coverage and techniques are documented and approved. Practices for
specific geometries such as spot welds are not included. The practice is intended to be used on
thicknesses of 9 to 200 mm. Greater and lesser thicknesses may be examined using this practice if
the technique can be demonstrated to provide adequate detection on mockups of the same wall
thickness and geometry.
看来很厉害啊!!!
|
|
|