ASTM A1016 Info

mechen

ASTM Identifier	ASTM A1016/A1016M 13
Revision Number	2013 EDITION
Title	Standard Specification for General Requirements for Ferritic  Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
Status	Current
Modification Type	Revision
Publication Date	April 1, 2013, midnight
Document Type	Specification
Page Count	11
Changes from the previous issue	A redline edition is available for this document, with all  changes visible. Ask Document Center Inc. for more information (http://www.document-center.com/).
Scope	1.1 This specification covers a group of requirements that,  unless otherwise specified in an individual specification, shall apply to the  ASTM product specifications noted below.        Title of Specification         ASTM     DesignationA                         Seamless    Carbon-Molybdenum Alloy-Steel Boiler and      Superheater    Tubes         A209/A209M         Seamless    Ferritic and Austenitic Alloy-Steel Boiler, Superheater,      and    Heat-Exchanger Tubes         A213/A213M         Welded    Austenitic Steel Boiler, Superheater, Heat-Exchanger,      and Condenser    Tubes         A249/A249M         Electric-Resistance-Welded    Ferritic Alloy-Steel Boiler and      Superheater    Tubes         A250/A250M         Seamless    and Welded Ferritic and Martensitic Stainless Steel      Tubing for    General Service         A268/A268M         Seamless    and Welded Austenitic Stainless Steel Tubing for      General    Service         A269         Seamless    and Welded Austenitic Stainless Steel Sanitary Tubing         A270         Seamless    and Welded Carbon and Alloy-Steel Tubes for      Low-Temperature    Service         A334/A334M         Welded    Austenitic Stainless Steel Feedwater Heater Tubes         A668/A668M         Austenitic    Stainless Steel Tubing for Breeder Reactor Core      Components         A771/A771M         Seamless    and Welded Ferritic/Austenitic Stainless Steel Tubing      for General    Service         A789/A789M         Welded    Ferritic Stainless Steel Feedwater Heater Tubes         A803/A803M         Austenitic    and Ferritic Stainless Steel Duct Tubes for Breeder      Reactor Core    Components         A826/A826M         High-Frequency    Induction Welded, Unannealed Austenitic Steel      Condenser    Tubes         A851        A These designations refer to the latest issue of the respective  specifications.    1.2 In the case of conflict between a requirement of a  product specification and a requirement of this general requirements  specification, the product specification shall prevail. In the case of  conflict between a requirement of the product specification or a requirement  of this general requirements specification and a more stringent requirement  of the purchase order, the purchase order shall prevail.    1.3 The values stated in either SI units or inch-pound  units are to be regarded separately as standard. Within the text, the SI  units are shown in brackets. The values stated in each system may not be  exact equivalents; therefore, each system shall be used independently of the  other. Combining values from the two systems may result in non-conformance  with the standard. The inch-pound units shall apply unless the “M”  designation (SI) of the product specification is specified in the order.
Keywords	alloy steel tube; austenitic stainless steel; duplex stainless  steel; ferritic stainless steel; ferritic/austenitic stainless steel; heavily  cold-worked steel tube; seamless steel tube; stainless steel tube; steel  tube; welded steel tube; ICS Number Code 77.140.20 (Steels of high quality)
Abstract	This specification covers  general requirements for ferritic alloy steel, austenitic alloy steel, and  stainless steel tubes. The steel shall made by any process. The material  shall conform to the tensile property requirements prescribed in the  individual product specification. Yield strength tests and elongation tests  shall be made to conform to the requirements. Flattening test, reverse  flattening test, reverse bend test, flaring test, flange test, hardness test,  ultrasonic test, eddy current test, flux leakage test, and hydrostatic test  shall be made to conform to the requirements specified.
Committee Number	A01.10
To find similar documents by ASTM Volume:	01.01 (Steel--Piping, Tubing, Fittings)
To find similar documents by classification:	77.140.20 (Stainless steels)

liuyu1029

-
沙发，谢分享，顶楼主

阿谢克那·李

顶起mechen，顶顶！

明月照积雪

谢谢分享！！！！！